Cavity Slider Waterstop Building Codes & Rules


- Waterstop Angle Tools™ simplifies the National Construction Code (NCC) with interactive graphics, including deemed to comply & best practices.


M

Top of Membrane

M

M

Wall Lining

  • Adhere to cavity doorset

Tools™ Best Practice

Split JambTools™ Best Practice

  • Never embed in Tiles
  • Prime cut ends
  • Seal under ends to Tiles

Tools™ Best Practice

Waterstop Angle at CavityTools™ Best Practice

  • 2mm gap to Jamb to allow for movement
  • Mitre cut bottom web & fold 90° to prevent leak into cavity
  • File smooth all edges
  • Sealant to all edges & junctions

Finishes

NCC 2022 HP, 10.2.2 (1) (c)

AS 3740:2021, 4.11.2 (b)

≥ 40NCC 2022 HP, 10.2.2 (1) (c)AS 3740:2021, 4.11.2 (b)

Cavity Sliding Door

Sealant / Adhesive

Split Jamb

Sealant bead

Sealant Joint

Split Jamb

Finished Floor Level

Membrane

Manufacturer's Requirement

8Manufacturer's Requirement

Industry Recommendation

PrimerIndustry Recommendation

  • Compatible with both Substrate Material & WPM System
  • Non-porous Angle
  • Porous Floor

Tools™ Best Practice

Mechanical FixingsTools™ Best Practice

  • 200mm centres

NCC 2022 HP, 10.2.24 (a) (ii)

AS 3740:2021, 4.9.1 (c) (iii)

≥ 50NCC 2022 HP, 10.2.24 (a) (ii)AS 3740:2021, 4.9.1 (c) (iii)

NCC 2022 HP, 10.2.24 (c)

AS 3740:2021, 4.9.1 (a) (i)

Top of Waterstop ≥ FFLNCC 2022 HP, 10.2.24 (c)AS 3740:2021, 4.9.1 (a) (i)

Sealant over anchor screws

Industry Recommendation

Water CheckIndustry Recommendation

  • ≤ 3mm prevents spilt water / unintentional overflows discharging over angle

NCC 2022 HP, 10.2.24

Industry Recommendation

Industry Recommendation

Waterstop Angle

Internal Waterproofing Overview

Waterstop


  • ≥ 40mm set down[1]
  • ≥ 25mm Screed depth to be maintained when calculating Falls throughout the wet area[2]
  • Sealant beads & fillets to protect Membrane[3]


Waterstop RULES


NCC 2022 V2


All Building Classes


NCC 2022 F2D2, S26C3, & Part 10.2.11 to 13 [2019 F1.7]


May 2023



AS 3740:2021, 3.3.1 (a)

AS 3740:2021, 3.3.3 (a) (iv)

AS 3740:2021, 4.9

AS 3740:2021, 3.3.3 (b) (ii)

AS 3740:2021, 3.3.1 (c)

Step up PROS & CONS


NCC 2022 V1


Water Stop INSTALLATION


NCC 2022 V1


NCC 2022 HP, 10.2.2 (1) (c)

AS 3958.1:2007, 3.3.3.1 (e)

AS 3740:2021, 4.9.1 (d) (ii)

Substrate


  • CSP 2 -5 (Concrete Surface Profile)[1]
  • Smooth Wood Float equivalent finish
  • Smooth & clean before waterproofing[2]
  • No ribs, ridges or over-trowelling


Substrate MATERIALS


NCC 2022 V3


All Building Classes


NCC 2022 F2D2, S26C3, & HP10.2.24 [2019 F1.7, 3.8.1]


May 2023



AS 3740:2021, 3.3.2 (a)

AS 3740:2021, 3.3.2 (b)

NCC 2022 HP, 10.2.1

NCC 2022 Vol 1, F2D2

NCC 2022 Vol 1, S26C3 (1)

Substrate PREPARATION


NCC 2022 V1


Substrate PREPARATION


NCC 2022 V6


All Building Classes


NCC 2022 F2D2, S26C3, & HP10.2.9 [2019 F1.7]


May 2023



AS 3740:2021, 4.4.1

NCC 2022 Vol 1, F2D2

NCC 2022 Vol 1, S26C3 (1)

NCC 2022 HP, 10.2.9

  • Building elements in Wet Areas to be Waterproof or Water Resistant to the NCCAS 3740:2021, 4.4.1NCC 2022 Vol 1, F2D2NCC 2022 Vol 1, S26C3 (1)
  • All surfaces to be prepared for Waterproofing System adhesionNCC 2022 HP, 10.2.9
  • Smooth, dust-free, clean & dry surface
  • Fill voids
  • Grind smooth any protrusions
  • Free of formwork deformity
  • Prime substrate to prohibit pin-holing during the membrane curing process
  • Moisture test & apply primer as per Manufacturer's Recommendations

AS 3740:2021, 4.4.1

AS 3740:2021, 4.4.1

Junctions


  • ≥ 12mm[1] Bond breaker Fillet to all Class III Membrane Junctions


Junction RULES


NCC 2022 V4


All Building Classes


NCC 2022 F2D2, S26C3, & Part 10.2.24 [2019 F1.7, 3.8.1]


May 2023



AS 3740:2021, 4.10

AS 3740:2021, 4.13.2.2

  • NCC 2022 F2D2, S26C3, & Part 10.2.24 [2019 F1.7, 3.8.1]
  • Building elements in Wet Areas to be Waterproof or Water Resistant to NCC Specification 26, NCC Part 10.2, & AS 3740
  • Backing rod, tape, or sealant should be installed when the membrane is bonded to the substrate
  • Type depending on membrane flexibility classAS 3740:2021, 4.10

Class I Membrane (low extensibility)

  • Resin systems, or water-based epoxies membranes
  • ≥ 6mm ØAS 3740:2021, 4.13.2.2 backing rod should be installed to allow the membranes to flex instead of stretch, with a continuous tape between backing rod and membrane to keep it in place

Class II Membrane (medium extensibility)

  • Acrylic membranes, bitumen-based emulsions or mastics membranes
  • Tape to allow the membrane to stretch

Class III Membrane (high extensibility)

  • Polyurethane, PVC, rubber, or EPDM membrane
  • Fillet or sealant to allow even thickness to the membrane

AS 3740:2021, 4.10

Wall Linings


  • 6mm Fibre-cement for typical Tile or Paint finish
  • 8mm gap to Structural Floor


Wall Lining


NCC 2022 V2


  • 6mm Fibre-cement for typical Tile or Paint finish
  • 8mm gap to Structural Floor
Redirecting... (5)
Please wait while we redirect you to the correct page.